I. Core Functions of Shielding Gas
Oxidation and Contamination Prevention:
Isolates the weld pool from air (oxygen, moisture) to avoid oxidation, nitridation, or porosity (e.g., titanium alloys react with oxygen to form brittle phases).
Plasma Regulation:
Suppresses plasma formation at high power, preventing laser energy from being shielded (e.g., helium's high ionization energy reduces plasma formation).
Control of Melt Pool Behavior:
Influences melt pool flow through gas thermal conductivity and density, adjusting penetration depth and width (e.g., helium increases thermal conductivity for deeper penetration in thick materials).
Cooling and Cleaning:
Blows away spatter and slag, aiding in cooling and improving weld formation.

II. Selection Criteria
1. Material Properties
Carbon Steel/Low-Alloy Steel:
Prioritize pure argon (prevents oxidation, ensures smooth welds) or nitrogen (cost-effective, reduces spatter but requires controlled flow to avoid iron nitride brittleness). Argon-nitrogen mixtures (balance cost and performance) are also suitable.
Stainless Steel:
Use pure argon (prevents chromium oxidation and intergranular corrosion). For thick plates, add helium (e.g., argon-helium mixtures) to increase penetration via high thermal conductivity.
Aluminum/Aluminum Alloys:
Pure argon shields against oxygen to avoid aluminum oxide inclusions. For thick plates or high-speed welding, use high-helium mixtures (e.g., 70% He + 30% Ar) to reduce surface tension and improve melt flow.
Copper/Copper Alloys:
Due to copper's low laser absorption, use pure helium or high-helium mixtures to enhance energy utilization and penetration. Pure argon may cause poor melt flow.
Titanium Alloys:
Require high-purity argon (≥99.99%) to strictly isolate oxygen and nitrogen (risk of brittle phases). Complex structures need dual-sided shielding (front and back gas flows).
Galvanized Steel:
Nitrogen or argon-nitrogen mixtures reduce zinc vaporization (low boiling point causes porosity), but flow rate must be controlled to avoid excessive cooling.
2. Welding Power and Process Type
Low Power (<1kW):
Choose pure argon for cost-effectiveness and stable oxidation protection.
High Power (>1kW) Deep Penetration Welding:
Use helium or argon-helium mixtures to suppress plasma and enhance energy penetration. For conduction welding, opt for argon or nitrogen to control melt pool size and prevent burn-through.
Pulse Welding:
Avoid nitrogen (prone to spatter); prioritize argon. For continuous welding, adjust based on material (e.g., nitrogen for carbon steel).
3. Gas Characteristics Comparison
Argon (Ar):
Advantages: Low cost, versatility (suitable for most metals like stainless steel, aluminum, titanium), stable arc, and good weld formation.
Limitations: Prone to plasma ionization at high power, affecting energy transmission.
Helium (He):
Advantages: Plasma resistance, deep penetration, high welding speed (ideal for copper and thick aluminum), but expensive (10–20x argon cost) and requires enclosed environments to prevent diffusion loss.
Nitrogen (N₂):
Advantages: Lowest cost, suitable for carbon steel and galvanized steel, reduces spatter.
Limitations: Reacts with aluminum and titanium to form brittle phases; forbidden for these materials.
4. Additional Factors
Purity Requirements:
Sensitive materials (stainless steel, titanium) need ≥99.999% high-purity gas, with strict control of moisture (dew point < -40°C) and oxygen content.
Gas Flow Parameters:
Typically use coaxial or lateral gas flow at 5–30 L/min (excessive flow causes turbulence; insufficient flow leads to poor shielding).
Backside Shielding:
Thin-walled or single-sided welded parts require backside gas (e.g., pure argon) to prevent rear oxidation.
III. Common Gas Combinations and Applications
Pure Argon:
Widely used for stainless steel, aluminum, and titanium in low-to-medium power welding.
Argon-Helium Mixtures:
For thick aluminum and copper alloys, balancing penetration and cost (e.g., 30% Ar + 70% He).
Argon-Nitrogen Mixtures:
For carbon steel and low-alloy steel, reducing spatter and cost (5–10% nitrogen; higher ratios may harden the weld).
Pure Helium:
Reserved for high-power deep penetration welding (copper, thick aluminum) to suppress plasma.
Pure Nitrogen:
Only for carbon steel surface sealing and galvanized steel; strictly avoid with aluminum and titanium.
IV. Key Considerations
Gas Purity and Cleanliness:
Ensure pipelines and cylinders are dry and clean to prevent moisture or oil contamination.
Dynamic Adjustment:
Increase helium ratio for high-speed/thick plate welding; reduce flow for thin plates/low-speed welding to avoid excessive cooling.
Dual-Sided Shielding:
For airtight components (e.g., pressure vessels), protect both front and back surfaces during welding.








