The causes and solutions for the occurrence of pores during laser welding

Jun 16, 2025 Leave a message

The causes and solutions for the occurrence of pores during laser welding

n2025051417184384541

 

1. Types of Porosity

 

Porosity in laser welding typically manifests in three primary forms: hydrogen porosity, nitrogen porosity, and CO porosity. Hydrogen porosity appears as small, spherical voids with smooth surfaces, often located near the weld center or fusion line. Nitrogen porosity tends to be irregularly shaped with sharp edges and frequently clusters on the weld surface. CO porosity, common in deep-penetration welds, exhibits a distinctive tadpole-like shape with a trailing tail, usually found in thicker weld sections.

 

2. Primary Causes and Corrective Measures

 

Shielding Gas Problems
Inadequate shielding gas coverage is a leading cause of porosity. Impurities in the gas (such as oxygen levels exceeding 50 ppm in argon) or improper flow rates can allow atmospheric contamination. Turbulence from excessive gas flow or insufficient coverage due to low flow rates both contribute to porosity. Solutions include using ultra-high-purity argon (99.999%), optimizing gas flow (typically 8–15 L/min, with higher rates for reactive metals like aluminum), and ensuring proper nozzle alignment. Dual-gas shielding systems (e.g., helium for inner shielding and argon for outer coverage) can further enhance protection.

Material Surface Contamination
Oil, grease, oxide layers, or coatings on the workpiece surface can introduce gas-forming elements into the weld pool. For example, aluminum's oxide layer (Al₂O₃) melts at 2050°C-far above the base metal's melting point-leading to incomplete fusion and gas entrapment. Zinc-coated steels pose a similar challenge, as zinc vaporizes at 907°C, creating porosity. Pre-weld cleaning via mechanical abrasion followed by solvent degreasing (e.g., ultrasonic acetone baths) is essential. For galvanized metals, beam oscillation techniques help vent zinc vapor, while preheating (150–200°C) reduces vaporization intensity.

Improper Welding Parameters
Excessive laser power can cause violent keyhole collapse, trapping gas, while insufficient power may fail to fully penetrate the material. Travel speed also plays a critical role-too fast, and gas bubbles cannot escape; too slow, and excessive heat input enlarges the melt pool, increasing gas solubility. Optimal parameters vary by material but often involve balancing power (e.g., 800W for 1mm stainless steel), speed (3 m/min), and focus position (slight positive defocus to stabilize the keyhole). Implementing power ramp-up at weld initiation can further minimize instability.

Keyhole Instability in Deep-Penetration Welds
In high-power laser welding, the keyhole (a vapor channel formed by laser ablation) may collapse unpredictably, trapping gas. Mitigation strategies include reducing power density (e.g., enlarging beam spot size to 0.2–0.4mm) or introducing filler wire (e.g., ER4043 aluminum wire, which absorbs hydrogen). Beam oscillation (50Hz, 1mm amplitude) promotes better metal flow and gas escape.

Environmental and Material Factors
Ambient humidity introduces hydrogen via water vapor dissociation, exacerbating porosity in hygroscopic metals like aluminum and magnesium. Controlling workshop humidity (<40%) and pre-drying materials (120°C for 1–2 hours) are effective countermeasures. Material composition also matters: aluminum's hydrogen solubility drops sharply during solidification, while sulfur/phosphorus in stainless steel forms low-melting compounds that trap gas. Using low-impurity filler metals (e.g., 5083 aluminum) or grain-refining additives (yttrium/zirconium) can improve results.

 

3. Detection and Remediation

 

Pre-weld material analysis (spectroscopy for O/H/S content) and real-time process monitoring (high-speed cameras to observe melt pool dynamics) help prevent porosity. Post-weld inspection via X-ray radiography detects sub-surface voids (>0.1mm). For repairs, localized grinding followed by low-power laser rewelding is often successful, provided surface oxides are fully removed.

 

4. Advanced Mitigation Techniques

 

In critical applications, vacuum laser welding (10⁻³Pa) eliminates gas interference entirely, though cost-prohibitive for most industries. Ultrasonic-assisted welding (20kHz vibration) disrupts bubble formation, reducing porosity by up to 70%. Emerging technologies like plasma spectroscopy (e.g., IPG's LASERDYNE) enable real-time parameter adjustments by analyzing weld plume emissions.

 

Conclusion


Porosity control requires a systematic approach-optimizing shielding, cleanliness, parameters, and environment. By implementing these measures, defect rates can meet stringent standards (e.g., <0.5% for automotive welds). Documenting procedures in a Welding Procedure Specification (WPS) ensures consistency across production runs.

 

    --Rayther Laser Camila Wang

Send Inquiry

whatsapp

Phone

E-mail

Inquiry